電気回路/zynq/Petalinux のビルド のバックアップ差分(No.14)
更新- バックアップ一覧
- 現在との差分 を表示
- ソース を表示
- バックアップ を表示
- 電気回路/zynq/Petalinux のビルド へ行く。
- 追加された行はこの色です。
- 削除された行はこの色です。
[[公開メモ]]
* 概要 [#y122c6a2]
Petalinux はオープンソースの Xilinx Linux とは別物。Xilinx が開発しています。
登録は必要だが無料で使えます。
とりあえず以下では z-turn ボード用にコンパイルして、Linux が(ギリギリ)起動するところまで進みました。
続編として、開発用にカスタマイズする手順はこちら > [[電気回路/zynq/Petalinux のカスタマイズ]]
全体の流れはこちら > [[電気回路/zynq]]
#contents
* ダウンロード [#w38e9003]
https://www.xilinx.com/support/download/index.html/content/xilinx/en/downloadNav/embedded-design-tools.html
ここから petalinux-v2016.4-final-installer1.run のようなファイルを落とす。
https://japan.xilinx.com/support/answers/68370.html
によれば v2016.4 のカーネルバージョンは 4.6 だそうだ。
* 環境は Ubuntu 16.04 LTS [#be55f93b]
VirtualBox に入れた Ubuntu 16.04 LTS 上で開発環境構築を行います。
始め Debian 9 で試したのですが、libtool の実行ファイルの名前が違う、
libc6 のバージョンコンフリクトで mknod, mknodat が見つからず
"No real function for mknod" などのエラーで止まる、
などややこしいことが起こり、断念しました。
今時 VirtualBox で気軽に OS を準備できますので、
Petalinux の推奨する環境を選ぶのが無難そうです。
[[>>> VirtualBox への Ubuntu 16.04 LTS の導入はこちらで紹介しました>電気回路/zynq/VirtualBox に Ubuntu 16.04 LTS を入れる]]
* インストール [#q2587901]
推奨環境やインストール方法は、~
https://japan.xilinx.com/support/documentation-navigation/development-tools/software-development/petalinux-tools.html から
ug1144-petalinux-tools-reference-guide.pdf にあります。
先に petalinux が要求するパッケージを入れます。
diffstat xvfb chrpath xterm libtool socat autoconf unzip texinfo gcc-multilib libsdl1.2-dev libglib2.0-dev zlib1g:i386 は上記ガイドに書かれていませんが、
インストール時に入れろと言われます。
(言われた瞬間に ^Z で中断して、これらのパッケージをインストールしてから再開すれば、
問題なく続行できるようでした。インストーラーの中身をチェックして、解凍して、動き出すまでに
ものすごく待たされるので、この対処法はかなり重要です)
LANG:console
$ sudo apt-get install build-essential binutils ncurses-dev u-boot-tools file
$ sudo apt-get install tofrodos iproute2 gawk net-tools libncurses5-dev tftp tftpd-hpa zlib1g-dev libssl-dev flex bison libselinux1
$ sudo apt-get install diffstat xvfb chrpath xterm libtool socat autoconf unzip texinfo gcc-multilib libsdl1.2-dev libglib2.0-dev zlib1g:i386
petalinux のインストーラは巨大なバイナリを含んだ bash スクリプトです。
bash スクリプトなので実行権限が無くても bash に読ませれば実行できます。
インストーラを root で走らせると途中で以下のエラーが出ます。
ERROR: The extensible sdk cannot be installed as root.
ERROR: Failed to install Yocto SDK for zynqMP.
一方、インストーラを 非root で走らせると、/opt などのルート権限の
必要なフォルダにはインストールできません。
Web上では /opt の下にインストールする例も多いですが、
基本的にこのインストーラは、ユーザー権限で動かして、
ユーザーのホームの下のフォルダへインストールすることが想定されているようです。
(インストール後に単に mv でフォルダを動かしても動作しないと書かれていましたし)
ここでは ~/z-turn/petalinux へインストールすることにしました。
[必要ディスク容量]~
ところでこれ、元のインストールファイルが大きく、/tmp に展開される
ファイルも大きく、インストール後の容量も大きいので、インストールファイル
ダウンロード前の VirtualBox の空き容量が 30GB 弱だと、途中で Disk Full
になりました。35GB もあればインストールは大丈夫そうですが、
VirtualBox の可変サイズの仮想ディスクは、実際に使わない限り実ディスクを
圧迫しないので、作成時には十分大きな値を設定しておくのが良さそうです。
インストール後にインストーラを削除した段階ではシステム全体の使用容量は 15.9 GB でした。
このページの一番下で、いろいろ四苦八苦しながら Linux が起動したところで、
- システム全体で 24GB
- 開発のための ~/z-turn 以下は 20GB
程度でした。
LANG:console
$ bash petalinux-v2016.4-final-installer1.run -h
PetaLinux installer.
Usage:
petalinux-v2016.4-final-installer1.run [--log <LOGFILE>] [INSTALL_DIR]
Options:
--log <LOGFILE> specify where the logfile should be created.
it will be petalinux_installation_log
in your working directory by default.
[INSTALL_DIR] specify the directory where you want to
install the tool kit. If not specified,
it will install to your working directory.
$ mkdir ~/z-turn/petalinux
$ # インストールに sudo はしません
$ bash petalinux-v2016.4-final-installer1.run ~/z-turn/petalinux
INFO: Checking installer checksum...
INFO: Extracting PetaLinux installer...
INFO: Installing PetaLinux...
INFO: Checking PetaLinux installer integrity...
INFO: Extracting Installation files...
# ここまで、ものすごく時間がかかります
LICENSE AGREEMENTS
PetaLinux SDK contains software from a number of sources. Please review
the following licenses and indicate your acceptance of each to continue.
You do not have to accept the licenses, however if you do not then you may
not use PetaLinux SDK.
Use PgUp/PgDn to navigate the license viewer, and press 'q' to close
Press Enter to display the license agreements
Do you accept Xilinx End User License Agreement? [y/N] > y
Do you accept Webtalk Terms and Conditions? [y/N] > y
Do you accept Third Party End User License Agreement? [y/N] > y
INFO: Checking installation environment requirements...
INFO: Checking free disk space
INFO: Checking installed tools
INFO: Checking installed development libraries
INFO: Checking network and other services
INFO: Installing PetaLinux SDK to "/home/osamu/z-turn/petalinux/." # これもかなりかかる
INFO: Installing PetaLinux zynqMP Yocto SDK to "/home/osamu/z-turn/petalinux/./components/yocto/source/aarch64"...
PetaLinux Extensible SDK installer version 2016.4
=================================================
You are about to install the SDK to "/home/osamu/z-turn/petalinux/components/yocto/source/aarch64".
Proceed[Y/n]? Y
Extracting SDK...............................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /home/osamu/z-turn/petalinux/components/yocto/source/microblaze_lite/environment-setup-microblazeel-v10.0-bs-cmp-ml-xilinx-linux
INFO: PetaLinux Yocto SDK for microblaze has been successfully installed.
INFO: PetaLinux SDK has been installed to /home/osamu/z-turn/petalinux/.
* 環境変数の設定 [#v45a3c2e]
LANG:console
$ source ~/z-turn/petalinux/settings.sh
PetaLinux environment set to '/home/osamu/z-turn/petalinux'
WARNING: /bin/sh is not bash!
bash is PetaLinux recommended shell. Please set your default shell to bash.
INFO: Checking free disk space
INFO: Checking installed tools
INFO: Checking installed development libraries
INFO: Checking network and other services
$ echo $PETALINUX
/home/osamu/z-turn/petalinux
$ arm-linux-gnueabihf-gcc --version
arm-linux-gnueabihf-gcc (Linaro GCC 5.2-2015.11-2) 5.2.1 20151005
Copyright (C) 2015 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
$ arm-none-eabi-gcc --version
arm-none-eabi-gcc (Linaro GCC 5.2-2015.11-2) 5.2.1 20151005
Copyright (C) 2015 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
$
パッケージ使用状況のサーベイを off にする
LANG:console
$ petalinux-util --webtalk off
INFO: Turn off webtalk feature!
* 新しいプロジェクトを作る [#aabc4100]
z-turn ボード用にビルドしたいのだけれど、公式にはサポートされていないので、
zynq 用の汎用テンプレートを使って作る。
LANG:console
$ cd ~/z-turn
$ petalinux-create -t project --template zynq -n zturn-v2016.4
INFO: Create project: zturn-v2016.4
INFO: New project successfully created in /home/osamu/z-turn/zturn-v2016.4
$ cd zturn-v2016.4
$ git init
Initialized empty Git repository in /home/osamu/z-turn/zturn-v2016.4/.git/
$ cat <<EOT > .gitignore
.petalinux
build
images
EOT
$ git add .
$ git config --global user.email "osamu@big.jp"
$ git config --global user.name "Osamu Takeuchi"
$ git commit -m "newly created"
$ ls project-spec/
attributes configs hw-description meta-user
どうやら project-spec/ というのが petalinux のプロジェクト本体のようだ。
* vivado のハードウェア設定を出力する [#a82e50cc]
Petalinux をビルドするには *.hdf ファイルが必要になります。
このファイルは vivado で Export Hardware すると得られます。
Linux を動作可能なPS設定を vivado へ食わせれば良いので、
ここでは z-turn についていた mys-xc7z020-trd.xpr から [File]-[Export]-[Export Hardware...]
しました。(参照:[[電気回路/z-turn/基本事項#qd72eb9b]])
&ref(電気回路/zynq/Linux に平行してベアメタルプログラムを走らせる/file-export-hardware.png,,66%);
[Include bitstream], [Local to Project] で OK
&ref(電気回路/zynq/Linux に平行してベアメタルプログラムを走らせる/export-including-bitstream.png,,66%);
この操作により、
(project dir)/(project-name).sdk/design_1_wrapper_hw_platform_0/*
に design_1_wrapper.bit, ps7_init.* や system.hdf が出力されます。
&ref(電気回路/zynq/Linux に平行してベアメタルプログラムを走らせる/exported-hardware-configuration.png,,66%);
* vivado のハードウェア設定を取り込みつつ基本の設定 [#y20ed9c0]
上記フォルダ(コピーしたもの)を指定して petalinux-config すると、
ハードウェア設定を取り込んだ後、いろいろ設定可能なメニューが現れます。
LANG:console
$ cd ~/z-turn/zturn-v2016.4
$ petalinux-config --get-hw-description=path/to/design_1_wrapper_hw_platform_1
INFO: Getting hardware description...
[INFO] generating Kconfig for project
[INFO] menuconfig project
/home/osamu/z-turn/zturn-v2016.4/build/misc/config/Kconfig.syshw:30:warning: defaults for cho
/home/osamu/z-turn/zturn-v2016.4/build/misc/config/Kconfig:546:warning: config symbol defined
configuration written to /home/osamu/z-turn/zturn-v2016.4/project-spec/configs/config
&ref(電気回路/zynq/Linux に平行してベアメタルプログラムを走らせる/petalinux-system-configuration.png,,66%);
とりあえず何も変更せずに Exit して設定を保存。
LANG:console
*** End of the configuration.
*** Execute 'make' to start the build or try 'make help'.
[INFO] sourcing bitbake
[INFO] generating plnxtool conf
[INFO] generating meta-plnx-generated layer
~/z-turn/zturn-v2016.4/build/misc/plnx-generated ~/z-turn/zturn-v2016.4
~/z-turn/zturn-v2016.4
[INFO] generating machine configuration
[INFO] generating bbappends for project . This may take time !
~/z-turn/zturn-v2016.4/build/misc/plnx-generated ~/z-turn/zturn-v2016.4
# ここでものすごく時間がかかります
~/z-turn/zturn-v2016.4
[INFO] generating u-boot configuration files
[INFO] generating kernel configuration files
[INFO] generating kconfig for Rootfs
Loading cache: 100% |##############################################################################################| ETA: 00:00:00
Loaded 2937 entries from dependency cache.
Parsing recipes: 100% |############################################################################################| Time: 00:00:05
Parsing of 2325 .bb files complete (2285 cached, 40 parsed). 2940 targets, 196 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
NOTE: Preparing RunQueue
NOTE: PN build list saved to 'pn-buildlist'
NOTE: PN dependencies saved to 'pn-depends.dot'
NOTE: Package dependencies saved to 'package-depends.dot'
NOTE: Task dependencies saved to 'task-depends.dot'
Generate rootfs kconfig
[INFO] oldconfig rootfs
[INFO] generating petalinux-user-image.bb
$
* まずはカーネルをビルドしてみる [#q69e8291]
LANG:console
$ petalinux-build --help
petalinux-build (c) 2005-2013 Xilinx, Inc.
Builds the project or the specified components.
Usage:
petalinux-build [options]
Required:
Options:
-h, --help show function usage
-p, --project <PROJECT> path to PetaLinux SDK project.
Default is working project.
-c, --component <COMPONENT> Specify the component
it will build the specified component and its dependencies
E.g. -c rootfs
E.g. -c myapp
-x, --execute <tasks of bitbake> Specify a bitbake task of the component
To know the list tasks for a component:
E.g. -x do_listtasks
-f,--force Force run a specific task ignoring the stamps
Force run has to be for a component or its tasks
E.g. -c myapp -f
E.g. -c myapp -x compile -f
-v, --verbose Show compile messages verbose mode
EXAMPLES:
Build the project:
$ petalinux-build
the bootable images are in <PROJECT>/images/linux/.
Build kernel only:
$ petalinux-build -c kernel
Compile kernel forcefully:
$ petalinux-build -c kernel -x compile -f
Deploy kernel forcefully:
$ petalinux-build -c kernel -x deploy -f
Build kernel and update the bootable images:
$ petalinux-build -c kernel
$ petalinux-build -x package
Build rootfs only:
$ petalinux-build -c rootfs
Build myapp of rootfs only:
$ petalinux-build -c rootfs/myapp
Clean up u-boot and build again:
$ petalinux-build -c u-boot -x distclean
## above command will remove the <PROJECT>/build/linux/u-boot/ directory.
$ petalinux-build -c u-boot
Clean up the project build and build again:
$ petalinux-build -x distclean
## above command will remove the <PROJECT>/build/ directory.
$ petalinux-build
Clean up the project build and the generated bootable images:
$ petalinux-build -x mrproper
## above command will remove <PROJECT>/images/ and <PROJECT>/build/ directories
他にもいろいろビルドできるらしい。
LANG:console
$ petalinux-build -c kernel
[INFO] building kernel
[INFO] sourcing bitbake
INFO: bitbake virtual/kernel
Loading cache: 100% |##############################################################################################| ETA: 00:00:00
Loaded 2938 entries from dependency cache.
Parsing recipes: 100% |############################################################################################| Time: 00:00:05
Parsing of 2325 .bb files complete (2291 cached, 34 parsed). 2940 targets, 196 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
NOTE: Preparing RunQueue
NOTE: Checking sstate mirror object availability (for 597 objects)
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
Currently 1 running tasks (851 of 1810):
0: linux-xlnx-4.6-xilinx+gitAUTOINC+2762bc9163-r0 do_compile (pid 17351)
# ここでかなり時間がかかる
# で、エラーが出た
ERROR: fsbl-0.2+xilinx+gitAUTOINC+ef07b552f4-r0 do_configure: Function failed: do_configure
(log file is located at /home/osamu/z-turn/zturn-v2016.4/build/tmp/work/cortexa9hf-neon-
xilinx-linux-gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-r0/temp/log.do_configure.13899)
ERROR: Logfile of failure stored in: /home/osamu/z-turn/zturn-v2016.4/build/tmp/work/cortexa9hf-
neon-xilinx-linux-gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-r0/temp/log.do_configure.13899
Log data follows:
| DEBUG: Executing python function sysroot_cleansstate
| DEBUG: Python function sysroot_cleansstate finished
| DEBUG: Executing shell function do_configure
| MISC_ARG is -yamlconf /home/osamu/z-turn/zturn-v2016.4/build/tmp/work/cortexa9hf-neon-
xilinx-linux-gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-r0/fsbl.yaml
| APP_ARG is -app "Zynq FSBL"
| cmd is: xsct /home/osamu/z-turn/zturn-v2016.4/build/tmp/work/cortexa9hf-neon-xilinx-linux-
gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-r0/app.tcl -ws /home/osamu/z-turn/zturn-v2016.4
/build/../components/plnx_workspace -pname fsbl -rp none -processor ps7_cortexa9_0 -hdf
/home/osamu/z-turn/zturn-v2016.4/build/tmp/deploy/images/plnx_arm/Xilinx-plnx_arm.hdf -arch 32
-app "Zynq FSBL" -yamlconf /home/osamu/z-turn/zturn-v2016.4/build/tmp/work/cortexa9hf-
neon-xilinx-linux-gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-r0/fsbl.yaml
| Starting SDK. This could take few seconds... Eclipse:
| An error has occurred. See the log file
| /home/osamu/z-turn/zturn-v2016.4/components/plnx_workspace/.metadata/.log.
| Eclipse:
| GTK+ Version Check
| XSCTHELPER INFO: Empty WorkSpace
| Starting SDK. This could take few seconds... Eclipse:
| An error has occurred. See the log file
| /home/osamu/z-turn/zturn-v2016.4/components/plnx_workspace/.metadata/.log.
| Eclipse:
| GTK+ Version Check
| timeout while establishing a connection with SDK
| while executing
| "error "timeout while establishing a connection with SDK""
| (procedure "getsdkchan" line 108)
| invoked from within
| "getsdkchan"
| (procedure "getprojects" line 19)
| invoked from within
| "getprojects -type hw"
| invoked from within
| "if { $params(ws) ne "" } {
| #Local Work Space available
| setws $params(ws)
| if { [catch {importprojects $params(ws)} result] } {
| puts "XSCTHELPER IN..."
| (file "/home/osamu/z-turn/zturn-v2016.4/build/tmp/work/cortexa9hf-neon-xilinx-linux-
gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-r0/app.tcl" line 111)
| WARNING: exit code 1 from a shell command.
| ERROR: Function failed: do_configure (log file is located at /home/osamu/z-turn/zturn-v2016.4
/build/tmp/work/cortexa9hf-neon-xilinx-linux-gnueabi/fsbl/0.2+xilinx+gitAUTOINC+ef07b552f4-
r0/temp/log.do_configure.13899)
ERROR: Task 592 (/home/osamu/z-turn/petalinux/components/yocto/source/arm/layers/meta-xilinx-
tools/recipes-fsbl/fsbl/fsbl_git.bb, do_configure) failed with exit code '1'
NOTE: Tasks Summary: Attempted 1797 tasks of which 1326 didn't need to be rerun and 1 failed.
Waiting for 0 running tasks to finish:
Summary: 1 task failed:
/home/osamu/z-turn/petalinux/components/yocto/source/arm/layers/meta-xilinx-tools/recipes-fsbl/fsbl/fsbl_git.bb, do_configure
Summary: There was 1 ERROR message shown, returning a non-zero exit code.
ERROR: Failed to build kernel
エラーが出ました。
言われたとおりログを見ると libgtk-x11-2.0.so.0 が見つからないといっているように見えるけれど、
ちゃんと /usr/lib/x86_64-linux-gnu に入っているし、このフォルダはロードパスに含まれている。
LANG:console
$ less /home/osamu/z-turn/zturn-v2016.4/components/plnx_workspace/.metadata/.log
...
!MESSAGE Application error
!STACK 1
java.lang.UnsatisfiedLinkError: Could not load SWT library. Reasons:
/home/osamu/.Xilinx/SDK/2016.4/org.eclipse.osgi/317/0/.cp/libswt-pi-gtk-4527.so: libgtk-x11-2.0.so.0: cannot open shared object file: No such file or directory
no swt-pi-gtk in java.library.path
Can't load library: /home/osamu/.swt/lib/linux/x86_64/libswt-pi-gtk-4527.so
Can't load library: /home/osamu/.swt/lib/linux/x86_64/libswt-pi-gtk.so
/home/osamu/.swt/lib/linux/x86_64/libswt-pi-gtk-4527.so: libgtk-x11-2.0.so.0: cannot open shared object file: No such file or directory
at org.eclipse.swt.internal.Library.loadLibrary(Library.java:327)
...
$ find /usr/lib -name "libgtk-x11-2.0*"
/usr/lib/x86_64-linux-gnu/libgtk-x11-2.0.so.0.2400.30
/usr/lib/x86_64-linux-gnu/libgtk-x11-2.0.so.0
$ echo $LD_LIBRARY_PATH
$ cat /etc/ld.so.conf
include /etc/ld.so.conf.d/*.conf
$ cat /etc/ld.so.conf.d/*
/usr/lib/x86_64-linux-gnu/libfakeroot
# Multiarch support
/lib/i386-linux-gnu
/usr/lib/i386-linux-gnu
/lib/i686-linux-gnu
/usr/lib/i686-linux-gnu
# libc default configuration
/usr/local/lib
# Multiarch support
/lib/x86_64-linux-gnu
/usr/lib/x86_64-linux-gnu
/usr/lib/x86_64-linux-gnu/mesa-egl
/usr/lib/x86_64-linux-gnu/mesa
# Legacy biarch compatibility support
/lib32
/usr/lib32
# Legacy biarch compatibility support
/libx32
/usr/libx32
** 言語設定が重要 LANG=C [#y0c5addb]
訳わからん!
となっていたところ、http://engineernote.hatenablog.com/entry/2016/02/15/010118 こちらで、
> PetaLinuxのビルドを行います。LANG=Cを忘れずに!
と書かれていました。
いやいや、そういう問題じゃなくて、ですね・・・
LANG:console
$ LANG=C petalinux-build -c kernel
[INFO] building kernel
[INFO] sourcing bitbake
INFO: bitbake virtual/kernel
Loading cache: 100% |###########################################################################################| ETA: 00:00:00
Loaded 2938 entries from dependency cache.
Parsing recipes: 100% |#########################################################################################| Time: 00:00:05
Parsing of 2325 .bb files complete (2291 cached, 34 parsed). 2940 targets, 196 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
NOTE: Preparing RunQueue
NOTE: Checking sstate mirror object availability (for 74 objects)
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
NOTE: Tasks Summary: Attempted 1810 tasks of which 1796 didn't need to be rerun and all succeeded.
INFO: Copying Images from deploy to images
INFO: Creating images/linux directory
[INFO] successfully built kernel
$ ls images/linux/
System.map.linux rootfs.cpio rootfs.tar.gz u-boot.bin vmlinux zynq_fsbl.elf
design_1_wrapper.bit rootfs.cpio.gz system.dtb u-boot.elf zImage
マジですか。
なんだかうまく行ってしまいました。
さらに、よくわからないのはビルドターゲットを kernel と指定しているにもかかわらず、
u-boot や fslb, rootfs などまでできてること。何なんでしょうね、これ。
* すべてビルド [#m1fec412]
LANG:console
$ LANG=C petalinux-build
[INFO] building project
[INFO] sourcing bitbake
INFO: bitbake petalinux-user-image
Loading cache: 100% |###########################################################################################| ETA: 00:00:00
Loaded 2938 entries from dependency cache.
Parsing recipes: 100% |#########################################################################################| Time: 00:00:05
Parsing of 2325 .bb files complete (2291 cached, 34 parsed). 2940 targets, 196 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
NOTE: Preparing RunQueue
NOTE: Checking sstate mirror object availability (for 68 objects)
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
NOTE: Tasks Summary: Attempted 1810 tasks of which 1806 didn't need to be rerun and all succeeded.
INFO: generating FIT Image
INFO: bitbake petalinux-user-image -c do_image_xilinx_fitimage -R /home/osamu/z-turn/zturn-v2016.4/build/conf/fit-image.conf
Parsing recipes: 100% |#########################################################################################| Time: 00:03:28
Parsing of 2325 .bb files complete (0 cached, 2325 parsed). 2940 targets, 196 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
NOTE: Preparing RunQueue
NOTE: Checking sstate mirror object availability (for 73 objects)
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
NOTE: Tasks Summary: Attempted 1322 tasks of which 1307 didn't need to be rerun and all succeeded.
INFO: Copying Images from deploy to images
[INFO] successfully built project
$ ls images/linux/
System.map.linux image.ub rootfs.cpio.gz system.dtb u-boot.elf zImage
design_1_wrapper.bit rootfs.cpio rootfs.tar.gz u-boot.bin vmlinux zynq_fsbl.elf
$ tar ftz images/linux/rootfs.tar.gz | less
$ ls -l images/linux/image.ub
-rw-r--r-- 1 osamu osamu 9056008 2月 16 01:39 images/linux/image.ub
image.ub と rootfs.tar.gz ができた。
* ビルドの概要 [#m53ad53f]
make を使っていないので、どのようにビルドが進んでいるのか全然わからない。
気づいたことをここにまとめる。
- 成果は image/ にできる
- image/linux の内容は build/tmp/deploy/images/plnx_arm/ に作成したのをコピーしたもの
- build/sstate-cache を見る限り、かなり非人間的なことをしている
- build/tmp/work-shared/plnx_arm/kernel-source にカーネルソースがある
-
LANG:console
$ ls build/sstate-cache/00/
sstate:device-tree-generation:cortexa9hf-neon-xilinx-linux-gnueabi:xilinx+gitAUTOINC+11f81055d1:r0:cortexa9hf-neon:3:0011197a4f6f3b9759bbaeb0fa81dcbd_compile.tgz.siginfo
sstate:petalinux-user-image:plnx_arm-xilinx-linux-gnueabi:1.0:r0:plnx_arm:3:008af769240be40f1a713d1995b36264_image_complete.tgz.siginfo
* uImage の作成 [#g1057dbd]
カーネルイメージは上記で生成された image.ub に含まれているそうで、
実は以下に進むのに uImage を別途作成する必要は無いことが、後からわかりました。
# uImage を別にしておいた方が個別に書き換えられてうれしいので、~
# 後で image.ub じゃなくて uImage で起動するよう書き換えたい。
LANG:console
$ LANG=C petalinux-package --image -c kernel --format uImage
SDK environment now set up; additionally you may now run devtool to perform development tasks.
Run devtool --help for further details.
### Shell environment set up for builds. ###
You can now run 'bitbake <target>'
INFO: generating uImage
INFO: bitbake -R /home/osamu/z-turn/zturn-v2016.4/build/conf/kerneltype.conf virtual/kernel
Loading cache: 100% |###########################################################################################| ETA: 00:00:00
Loaded 2 entries from dependency cache.
Parsing recipes: 100% |#########################################################################################| Time: 00:03:21
Parsing of 2325 .bb files complete (1 cached, 2324 parsed). 2940 targets, 196 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
NOTE: Preparing RunQueue
NOTE: Checking sstate mirror object availability (for 75 objects)
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
NOTE: Tasks Summary: Attempted 1810 tasks of which 1778 didn't need to be rerun and all succeeded.
$ ls images/linux/
System.map.linux image.ub rootfs.cpio.gz system.dtb u-boot.elf vmlinux zynq_fsbl.elf
design_1_wrapper.bit rootfs.cpio rootfs.tar.gz u-boot.bin uImage zImage
すでに zImage ができているところから uImage を作るのにこんなに時間がかかるのはおかしすぎ。
賢いビルドが働いていない気がする???
始めから --format uImage としておかないと二度手間過ぎる。
あれ、二度手間とかじゃ無くて、すでにビルドが済んでいる状態でもう一度同じビルドを指示するだけで
ものすごく時間がかかるのか。何もやることは無いはずなのに、裏で何をやっているのだろう???
* BOOT.bin の作成 [#w888792f]
2016.4 のマニュアルにミスタイプがあるけれど、Zynq UltraScale+ MPSoC 用の記述と比べて考えると、
正しいのはこう
LANG:console
$ petalinux-package --boot --fsbl images/linux/zynq_fsbl.elf --fpga images/linux/design_1_wrapper.bit --u-boot --force
INFO: File in BOOT BIN: "/home/osamu/z-turn/zturn-v2016.4/images/linux/zynq_fsbl.elf"
INFO: File in BOOT BIN: "/home/osamu/z-turn/zturn-v2016.4/images/linux/design_1_wrapper.bit"
INFO: File in BOOT BIN: "/home/osamu/z-turn/zturn-v2016.4/images/linux/u-boot.elf"
INFO: Generating zynq binary package BOOT.BIN...
INFO: Binary is ready.
WARNING: Unable to access the TFTPBOOT folder /tftpboot!!!
WARNING: Skip file copy to TFTPBOOT folder!!!
$ ls
BOOT.BIN build components config.project images project-spec
image/ じゃなくてカレントフォルダにできちゃうのか orz
でも一応できた。
(オプションに --force を渡しておかないと、すでにファイルがあるときに上書きできません)
* SD カードにコピー [#ic481ee5]
http://engineernote.hatenablog.com/entry/2016/01/31/012227
によると、
> BOOT.binはbitstreamとFSBL、u-bootをひとつのバイナリに結合したもので、image.ubはkernelとrootfs、デバイスツリーのようです。
とのことなので、まっさらな FAT フォーマットの SD カードに BOOT.bin と image.ub だけ入れればいいらしい。
こうやってファイルをまとめられてしまうと、
一部だけ書き換えたいとき大変そうに思います・・・
もっと変更しやすい形にする方法を調べないと。
でもまずはこの形で起動まで持って行きたい。
* 起動中の問題をいろいろ解決 [#ybd92c28]
当然(?)、そのままではまともに起動しませんでした。
起動メッセージを見ながら1つ1つ解決していきます。
正しく動くとこんな風になるはず。~
http://engineernote.hatenablog.com/entry/2016/01/31/012227
** DONE ダイオードすら点かない [#h00d6c35]
ZYNQ の初期設定が済めばカード上の DONE 発光ダイオードが点るはずなのですが、
上記でできた BOOT.BIN ではそれすら点きません。
これではどうしようもありません。
BOOT.BIN の生成を、
LANG:console
$ petalinux-package --boot --fsbl ../design_1_wrapper_hw_platform_1/fsbl.elf --fpga images/linux/design_1_wrapper.bit --u-boot --force
のようにして、--fsbl に与える .elf を vivado から持ってきた fsbl.elf にしたところ、
正しく起動しました。
z-turn 付属のプロジェクトでは fsbl 生成コードにもカスタマイズが入っているのかもしれません?~
後で調べる必要がありそうです。
>>> その後分かったことには、UART のチャンネルを 1 にするカスタマイズが入っている他、
新しいライブラリコードでは SD カード関連にバグ(?)があるため起動しなかったようです
[[[電気回路/zynq/最新の fsbl で Linux が起動しない理由を調べる]]] で分かった
- Xilinx SDK の最新コードをちょっと直して U-BOOT をビルド
- Petalinux 標準の U-BOOT で動くようにハードウェア設定を変える
のどちらかで、最新の U-BOOT を使えるようになりました。
** FSBL [#ode1428c]
まずメッセージを出すのが fsbl
LANG:console
Xilinx First Stage Boot Loader
Release 2014.4 Aug 11 2015-18:06:38
Devcfg driver initialized
Silicon Version 3.1
Boot mode is SD
SD: rc= 0
SD Init Done
Flash Base Address: 0xE0100000
Reboot status register: 0x60600000
Multiboot Register: 0x0000C000
Image Start Address: 0x00000000
Partition Header Offset:0x00000C80
Partition Count: 3
Partition Number: 1
Header Dump
Image Word Len: 0x000F6EC0
Data Word Len: 0x000F6EC0
Partition Word Len:0x000F6EC0
Load Addr: 0x00000000
Exec Addr: 0x00000000
Partition Start: 0x000065D0
Partition Attr: 0x00000020
Partition Checksum Offset: 0x00000000
Section Count: 0x00000001
Checksum: 0xFFD14B7E
Bitstream
In FsblHookBeforeBitstreamDload function
PCAP:StatusReg = 0x40000A30
PCAP:device ready
PCAP:Clear done
Level Shifter Value = 0xA
Devcfg Status register = 0x40000A30
PCAP:Fabric is Initialized done
PCAP register dump:
PCAP CTRL 0xF8007000: 0x4C00E07F
PCAP LOCK 0xF8007004: 0x0000001A
PCAP CONFIG 0xF8007008: 0x00000508
PCAP ISR 0xF800700C: 0x0802000B
PCAP IMR 0xF8007010: 0xFFFFFFFF
PCAP STATUS 0xF8007014: 0x00002A30
PCAP DMA SRC ADDR 0xF8007018: 0x00100001
PCAP DMA DEST ADDR 0xF800701C: 0xFFFFFFFF
PCAP DMA SRC LEN 0xF8007020: 0x000F6EC0
PCAP DMA DEST LEN 0xF8007024: 0x000F6EC0
PCAP ROM SHADOW CTRL 0xF8007028: 0xFFFFFFFF
PCAP MBOOT 0xF800702C: 0x0000C000
PCAP SW ID 0xF8007030: 0x00000000
PCAP UNLOCK 0xF8007034: 0x757BDF0D
PCAP MCTRL 0xF8007080: 0x30800100
DMA Done !
FPGA Done !
In FsblHookAfterBitstreamDload function
Partition Number: 2
Header Dump
Image Word Len: 0x000182C0
Data Word Len: 0x000182C0
Partition Word Len:0x000182C0
Load Addr: 0x00400000
Exec Addr: 0x00400000
Partition Start: 0x000FD490
Partition Attr: 0x00000010
Partition Checksum Offset: 0x00000000
Section Count: 0x00000001
Checksum: 0xFF6BA0BE
Application
Handoff Address: 0x00400000
In FsblHookBeforeHandoff function
SUCCESSFUL_HANDOFF
FSBL Status = 0x1
** u-boot [#i553e859]
ここから U-Boot が起動しています。
LANG:console
U-Boot 2016.07 (Feb 15 2017 - 19:04:54 +0900)
DRAM: ECC disabled 1 GiB
MMC: sdhci@e0100000: 0
SF: Detected W25Q128BV with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
## Error: flags type check failure for "serverip" <= "AUTO" (type: i)
himport_r: can't insert "serverip=AUTO" into hash table
In: serial
Out: serial
Err: serial
Net: ZYNQ GEM: e000b000, phyaddr -1, interface rgmii-id
eth0: ethernet@e000b000
U-BOOT for
ethernet@e000b000 Waiting for PHY auto negotiation to complete....... done
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 10.225.225.104 (1257 ms)
Hit any key to stop autoboot: 0
ここでキー入力を待ち、
LANG:console
Device: sdhci@e0100000
Manufacturer ID: 27
OEM: 5048
Name: SD8GB
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
reading image.ub
9056008 bytes read in 504 ms (17.1 MiB/s)
## Loading kernel from FIT Image at 10000000 ...
Using 'conf@1' configuration
Verifying Hash Integrity ... OK
Trying 'kernel@0' kernel subimage
Description: Linux Kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x100000d4
Data Size: 3828576 Bytes = 3.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00008000
Entry Point: 0x00008000
Hash algo: sha1
Hash value: d64f030b600f0f9b4719b9aec3abb54d250dba3b
Verifying Hash Integrity ... sha1+ OK
## Loading ramdisk from FIT Image at 10000000 ...
Using 'conf@1' configuration
Trying 'ramdisk@0' ramdisk subimage
Description: ramdisk
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x103aa360
Data Size: 5212087 Bytes = 5 MiB
Architecture: ARM
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: sha1
Hash value: 893afc6ebe8b4e92eefa09fbb10d6536a6ab5a05
Verifying Hash Integrity ... sha1+ OK
## Loading fdt from FIT Image at 10000000 ...
Using 'conf@1' configuration
Trying 'fdt@0' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x103a6d28
Data Size: 13702 Bytes = 13.4 KiB
Architecture: ARM
Hash algo: sha1
Hash value: 93252290614dcfbbc551b6db5362ae326e816674
Verifying Hash Integrity ... sha1+ OK
Booting using the fdt blob at 0x103a6d28
Loading Kernel Image ... OK
Loading Ramdisk to 07b07000, end 07fff7b7 ... OK
Loading Device Tree to 07b00000, end 07b06585 ... OK
RAM ディスクやら何やらを設定しています。
** Kernel [#e2902ea8]
ここからカーネルです。
LANG:console
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx (osamu@ubuntu16lts) (gcc version 5.2.1 20151005 (Linaro GCC 5.2-2015.11-2) ) #1 SMP PREEMPT Wed Feb 15 18:59:55 JST 2017
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: zturn-v2016.4
bootconsole [earlycon0] enabled
cma: Reserved 16 MiB at 0x3f000000
Memory policy: Data cache writealloc
percpu: Embedded 12 pages/cpu @ef7d3000 s19776 r8192 d21184 u49152
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608
Kernel command line: console=ttyPS0,115200 earlyprintk
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1009252K/1048576K available (5286K kernel code, 230K rwdata, 1848K rodata, 1024K init, 222K bss, 22940K reserved, 16384K cma-reserved, 245760K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc07f793c (8127 kB)
.init : 0xc0800000 - 0xc0900000 (1024 kB)
.data : 0xc0900000 - 0xc0939ba0 ( 231 kB)
.bss : 0xc0939ba0 - 0xc09713a4 ( 223 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to f0802000
slcr mapped to f0804000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at f0804100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
timer #0 at f080c000, irq=17
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (1333.33 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0880000
zynq-pinctrl 700.pinctrl: zynq pinctrl initialized
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 5092K (c7b07000 - c8000000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=18 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) c 2001-2006 Red Hat, Inc.
bounce: pool size: 64 pages
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 146, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
bootconsole [earlycon0] disabled
ここで止まってしまった。
https://forums.xilinx.com/t5/Embedded-Linux/Kernel-hangs-at-quot-bootconsole-earlycon0-disabled-quot/m-p/634200
これっぽい。
現在の設計では、
- vivado で UART0 と UART1 が両方 ON になっていて、
- UART0 のピンはユーザーIOとしてピンへ出ているだけ
- UART1 は USB_UART につながっている
ので、UART1 を使わなければならないのだけど、UART0 を見に行ってしまっているっぽい。
LANG:console
$ less build/tmp/deploy/images/plnx_arm/plnx_arm-system.dts
...
chosen {
bootargs = "console=ttyPS0,115200 earlyprintk";
stdout-path = "serial0:115200ns";
};
aliases {
serial0 = "/amba/serial@e0001000";
ethernet0 = "/amba/ethernet@e000b000";
spi0 = "/amba/spi@e000d000";
};
...
serial@e0000000 {
compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "okay";
clocks = <0x1 0x17 0x1 0x28>;
clock-names = "uart_clk", "pclk";
reg = <0xe0000000 0x1000>;
interrupts = <0x0 0x1b 0x4>;
device_type = "serial";
port-number = <0x1>;
};
serial@e0001000 {
compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "okay";
clocks = <0x1 0x18 0x1 0x29>;
clock-names = "uart_clk", "pclk";
reg = <0xe0001000 0x1000>;
interrupts = <0x0 0x32 0x4>;
device_type = "serial";
port-number = <0x0>;
};
earlycon0 がどうしてちゃんと動いているのか謎。
起動時に現れる数秒入力待ちに ENTER キーで割り込んで、
LANG:console
Hit any key to stop autoboot: 0 (ENTER)
Zynq> setenv bootargs console=ttyPS1,115200 earlyprintk
Zynq> boot
としたところ、先へ進むことができた。
後で dts の書き換え方法を調べなければ。。。~
あるいは UART0, UART1 の出力ピンを入れ替えてしまおうか???
以下、冒頭で文字化けしたり、出力がダブっているのは、ttyPS1 を有効にしてから
earlycon0 を無効化しているので、その間両方から出力されているのだと思う。
** ttyPS1 に切り替え後 [#y7b6004d]
LANG:console
珮onsole [ttyPS1] enabled
console [ttyPS1] enabled
bootconsole [earlycon0] disabled
bootconsole [earlycon0] disabled
xdevcfg f8007000.devcfg: ioremap 0xf8007000 to f0870000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
m25p80 spi0.0: found w25q128, expected m25p80
m25p80 spi0.0: w25q128 (16384 Kbytes)
4 ofpart partitions found on MTD device spi0.0
Creating 4 MTD partitions on "spi0.0":
0x000000000000-0x000000500000 : "boot"
0x000000500000-0x000000520000 : "bootenv"
0x000000520000-0x000000fa0000 : "kernel"
0x000000fa0000-0x000001000000 : "spare"
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 149 (00:0a:35:00:1e:53)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
cdns-i2c e0004000.i2c: 400 kHz mmio e0004000 irq 142
cdns-i2c e0005000.i2c: 400 kHz mmio e0005000 irq 143
EDAC MC: ECC not enabled
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using DMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
Freeing unused kernel memory: 1024K (c0800000 - c0900000)
mmc0: new high speed SDHC card at address 0007
INIT: mmcblk0: mmc0:0007 SD8GB 7.42 GiB
mmcblk0: p1 p2
version 2.88 booting
FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
EXT4-fs (mmcblk0p2): warning: mounting fs with errors, running e2fsck is recommended
EXT4-fs (mmcblk0p2): recovery complete
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
random: dd urandom read with 3 bits of entropy available
Wed Feb 15 16:39:44 UTC 2017
Starting internet superserver: inetd.
INIT: Entering runlevel: 5
Configuring network interfaces... IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.24.1) started
Sending discover...
Sending discover...
macb e000b000.ethernet eth0: link up (1000/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 10.225.225.142...
Lease of 10.225.225.142 obtained, lease time 60000
/etc/udhcpc.d/50default: Adding DNS 10.225.225.2
done.
Starting Dropbear SSH server: Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCywAVngG8aPxPIv6O1mO+J54MulFaSbDp3piMMUh6pAnB/PuLiauEh8tUubhK+3Fl1qribJ9mSbiEOrrbsbLkNvWQQ4aVT4ERPfc+cSlzIUcE0k+LuaEJBM0qdRXviNQVPUU9lSN/AdnvBND7H3ltixNI8fMAnrzxCoKpnfDw9xjHzMzJx4EEaACWu+lgn7XjAZmJKzBpxFRloFEypuDwTrqz/XiLmvdrVyD+PtPiAGcD47w60Ni9a/GDPstu+m0bOUn+KnV187GFDv6s6QD0GhRjqtXmdcSuhWcIQgjoMR6feEwAz3QoDT6ZUSuRG/fwZwkwYvYqEzUAupUAezfx7 root@plnx_arm
Fingerprint: md5 7e:0a:66:19:94:30:ea:76:08:92:61:b0:01:31:52:e0
dropbear.
Starting syslogd/klogd: done
Starting tcf-agent: OK
# ここで長時間かかる
random: nonblocking pool is initialized
EXT4-fs (mmcblk0p2): error count since last fsck: 10
EXT4-fs (mmcblk0p2): initial error at time 11: ext4_mb_generate_buddy:756
EXT4-fs (mmcblk0p2): last error at time 46: ext4_mb_generate_buddy:756
ここで止まった。
でも、表示されたアドレス 10.225.225.142 へ ssh 接続したところ繋がったので、
システムがハングアップしているわけではなさそう。
本来ならここは、~
https://forums.xilinx.com/t5/Embedded-Linux/Petalinux-2016-4-boot-from-SD-with-ext4-rootfs/m-p/743890/highlight/true#M18164
のように、
LANG:console
PetaLinux 2016.4 plnx_arm /dev/ttyPS0
plnx_arm login:
と続いて、すぐにログイン可能になるはずなのですが、
今の場合 ttyPS0 ではなく ttyPS1 につないでくれないと表示されないので、
またもやシリアルポート違いで表示&入力受付されていないのだと思われます。
** ssh でつなぐ [#s9a01c56]
表示された 10.225.225.142 へ ssh で繋ぎに言ったところ、ユーザー名とパスワードを聞かれた。
ユーザーなんて作成していないのだけれど・・・
まさかの、
- ユーザー名 root
- パスワード root
で、繋がりました。
** 起動後の状態確認 [#c5e928b5]
LANG:console
login as: root
root@10.225.225.142's password: root
# ls /
bin dev home lib mnt root sbin tmp var
boot etc init media proc run sys usr
# df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 64 0 64 0% /dev
tmpfs 515876 32 515844 0% /run
tmpfs 515876 40 515836 0% /var/volatile
tmpfs 64 0 64 0% /dev
/dev/mmcblk0p1 65388 13290 52098 20% /run/media/mmcblk0p1
# ls /run/media/mmcblk0p1
BOOT.BIN System Volume Information image.ub
# mount
rootfs on / type rootfs (rw,size=504624k,nr_inodes=126156)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
devtmpfs on /dev type devtmpfs (rw,relatime,size=504624k,nr_inodes=126156,mode=755)
tmpfs on /run type tmpfs (rw,nosuid,nodev,mode=755)
tmpfs on /var/volatile type tmpfs (rw,relatime)
tmpfs on /dev type tmpfs (rw,relatime,size=64k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/mmcblk0p1 on /run/media/mmcblk0p1 type vfat (rw,relatime,fmask=0000,dmask=0000,allow_utime=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
* 起動はうまく行っている [#w71f3723]
というわけで、起動自体はうまく行っていることがわかります。
LANG:console
$ git add .
$ git commit -m "起動するようになった"
などとして保存しておきます。
ここまでの作業で、
- components/*
- project-spec/configs/*
- project-spec/hw-description/*
- project-spec/meta-plnx-generated/*
- project-spec/meta-plnx-user/*
にいろいろファイルができていて、
多分これらは必要に応じて編集していいファイルなのだと思います。
現状、ルートファイルシステムは RAM ディスクなので
z-turn のコンソールでルートファイルシステムを変更しても
再起動すると変更が失われてしまいますし、
ちょこちょこ書き換えながら開発していくには不向きな感じです。
次は、
- シリアルポートの指定がおかしい
- カーネル、bootargs、デバイスツリー、ロジック、ルートファイルシステム等を
別々に書き換えられる形にしたい
あたりを直したいところです。
>>> [[電気回路/zynq/Petalinux のカスタマイズ]] へつづく
* ちょいメモ [#e29a434c]
参考になりそうなWebページ
http://www.ritsumei.ac.jp/se/re/izumilab/lecture/16zybot/4_IOControl_PetaLinux.html
* 質問・コメント [#e69d9105]
#article_kcaptcha
**u-bootの文字化け等(2) [#f42bbccd]
>[[saka]] (&timetag(2017-05-21T11:48:14+09:00, 2017-05-21 (日) 20:48:14);)~
~
回答ありがとうございます。~
もう少し説明しますと、以下のような状況になっています。~
petalinux-configでU-boot config(other)にしてbuild後、BOOT.BINから.bitファイルを取り除く手順で作成したBOOT.BIN(491296byte)ではSDカードへのアクセスもなく、だんまりになります。~
wrapper.bitを入れたBOOT.BIN(2575072byte)では起動しますが、この時のシリアル出力が前の投稿の状態になります。~
なお、この時BOOTパーティションにはBOOT.BIN、devicetree.dtb(18308)、uImage(3675776)、system.bit.bin(2083850)、uEnv.txt(559)を入れています。~
~
zyboもUART1に接続されていますが、uEnv.txtでの設定はttyPS0の方がu-boot部分の文字化けはあるものの、それ以外はまともに表示してくれます。ちなみにuEnv.txtは、次のようにしています。~
bootargs=console=ttyPS0,115200 root=/dev/mmcblk0p2 rw rootwait earlyprintk rootfstype=ext4 devtmpfs.mount=1~
uenvcmd=run mmc_loadbit_fat && echo Copying Linux from SD to RAM... && mmcinfo && run load_image && bootm ${kernel_load_address} - ${devicetree_load_address}~
load_image=fatload mmc 0 ${kernel_load_address} ${kernel_image} && fatload mmc 0 ${devicetree_load_address} ${devicetree_image}~
mmc_loadbit_fat=echo Loading ${bitstream_image} to PL... && mmcinfo && fatload mmc 0 ${loadbit_addr} ${bitstream_image} && fpga loadb 0 ${loadbit_addr} ${filesize}~
~
まずは武内様の取り組まれた手順を確認しながら、bitファイルを取り除いたBOOT.BINで起動できる方法を模索していきたいと思います。~
//
- なかなかお役に立てずすみません。.bitを抜いた場合fsblの起動メッセージも出ないのでしょうか? -- [[武内(管理人)]] &new{2017-05-21 (日) 21:53:23};
- wrapper.bitを入れた場合にttyPS0の方がうまく行くのであれば、ttyPS0がUART1へ繋がっているのかもしれません?devicetreeでUART0が定義されていなかったり、UART1 -> UART0 の順に定義されていたりすると、そうなりそうに思います。 -- [[武内(管理人)]] &new{2017-05-21 (日) 21:57:12};
- 回答ありがとうございます。.bitを抜くと、全く何もでないです。文字化けも解決しませんが、もう少し頑張ってみます。 -- [[saka]] &new{2017-05-23 (火) 09:07:39};
#comment_kcaptcha
**u-bootの文字化け等 [#pbdb45b0]
>[[saka]] (&timetag(2017-05-19T07:37:37+09:00, 2017-05-19 (金) 16:37:37);)~
~
武内様の一連のHP、大変参考にさせていただいており、感謝申し上げます。~
2点、質問させてください。~
1.zybo,vivado2016.4の環境でPetalinuxのカスタマイズのページでu-bootの部分だけ文字化けが出てしまいます。uEnv.txtのbootargsをttyPS1に変更するとu-bootの文字化け+kernel部分の抜けになります。~
2.BOOT.BIN から .bit ファイルを取り除いたBOOT.BINではbootしません。~
以上の状態にはまっています。~
お忙しいところ、申し訳ありませんが、何かアドバイスをいただければ助かります。~
よろしくお願いいたします。~
//
- UARTで文字が化けるのはボーレートが間違っている可能性が高いように思います。記事は z-turn board に関するものです。zybo で ttyPS1 にする必要があるのかどうかは zybo の仕様をご確認下さい。[[電気回路/z-turn/基本事項#w03173b3]] に書いたとおりです。 -- [[武内(管理人)]] &new{2017-05-19 (金) 19:59:50};
- 「boot しない」というだけだと詳しい症状が分からないのですが、もし何のメッセージも出ないようであれば ZYNQ を正しく初期化できていないのかもしれません。SD カードから u-boot を読むために ZYNQ の設定がどこまで必要かが、ボードの構成によって異なるのかもしれません?この記事のように正しく起動する SD カードの設定と比較しながら地道に探る必要がありそうです。お力になれずすみません。 -- [[武内(管理人)]] &new{2017-05-19 (金) 20:03:53};
#comment_kcaptcha
Counter: 59422 (from 2010/06/03),
today: 12,
yesterday: 0